Polished concrete for industrial facilities
A hardened, light-reflective, low-maintenance floor produced from the slab you already own — no new material, no removal cycle, no re-coating every few years.
Signs this is your scope
- Facilities tired of re-coating the same floor
- Dusting slabs that contaminate product and racking
- Dark facilities that need better light reflectivity
- Floors that must be cleaned quickly and often
- Long-term maintenance cost reduction targets
Polished Concrete — execution
Densified, hardened surface
Chemical densifier reacts in the slab surface to reduce dusting and increase abrasion resistance.
Progressive polishing steps
Each diamond step refines the surface toward the agreed gloss level rather than jumping to a shine that will not last.
Chosen aggregate exposure
Cream, salt-and-pepper or aggregate exposure is agreed with you before we start, because it cannot be undone.
Stain-resistant guard
A penetrating guard is applied to help the finish resist industrial staining and simplify cleaning.
The full restoration sequence
Every JK project runs the same eight steps. This service is one part of it — and we will tell you which of the other steps your floor also needs.
Slab assessment and documentation
We walk the floor with the facility team, record slab condition, joint damage, coating type and moisture indicators, then map the area into workable zones.
- Existing coating identification
- Joint and crack mapping
- Slab hardness and profile check
- Zone and access plan
Coating and contaminant removal
Failed epoxy, paint, thinset, mastic and sealer are mechanically removed with HEPA dust extraction so the slab is clean and open before any repair work.
- Mechanical removal — no uncontrolled dust
- Epoxy, urethane, paint, adhesive residue
- Continuous vacuum containment
Joint, crack and spall repair
Forklift-damaged joint edges, spalls and cracks are cut, filled with semi-rigid material and ground flush so wheel traffic stops accelerating the damage.
- Joint edge rebuild
- Semi-rigid joint filler
- Spall and pop-out patching
- Crack routing and fill
Large-area diamond grinding
Planetary grinders with progressive diamond tooling flatten the surface, open the concrete and prepare a consistent profile across the whole area.
- Progressive metal-bond tooling
- Surface flattening
- Consistent profile for the chosen finish
Chemical hardening
A densifier is applied to harden the slab surface, cut down dusting and improve abrasion resistance under forklift and pallet traffic.
- Reduced dusting
- Higher surface abrasion resistance
- Better long-term cleanability
Polish, grind & seal or coat
Depending on the facility, the floor is resin-polished to the target gloss, grind-and-sealed for an economical industrial finish, or prepared for a coating system.
- Polished concrete
- Grind & seal
- Coating-ready surface profile
Guard and line work
Protective treatment is applied where required, and traffic markings or safety lines are re-established before the zone is handed back.
- Stain-resistant guard
- Traffic and safety line layout
- Zone handover checklist
Maintenance plan
We hand over a written maintenance routine so the facility team keeps the finish performing instead of re-entering the damage cycle.
- Cleaning method and chemistry
- Inspection interval
- Re-burnish / touch-up guidance
At a glance
| Best for | Manufacturing, warehouse, distribution, showroom-adjacent industrial space |
|---|---|
| Finish options | Cream / salt-and-pepper / aggregate exposure; matte to high gloss |
| Maintenance | Dry dust mop and auto-scrubber; periodic re-burnish |
| Advantage | No delamination risk — the finish is the slab, not a layer on top of it |
| Prerequisites | Slab in restorable condition, joints and cracks repaired, coating fully removed |
Questions we get on this scope
Is polished concrete slippery?
A clean, dry polished floor has comparable slip resistance to other hard industrial finishes, and traction treatments are available where wet processes exist. We discuss this against your actual operating conditions.
Can any slab be polished?
No, and we will tell you when yours cannot. Severely damaged, very soft or heavily contaminated slabs may be better served by grind & seal or resurfacing.
How is it maintained?
Routine dust mopping and auto-scrubbing with a neutral cleaner, plus periodic re-burnishing. We hand over a written maintenance routine at project close.
Start with a free floor assessment.
Tell us the facility type, approximate square footage and what the floor is doing today. We will walk the slab, document the condition and come back with a scope and schedule.